Language

Dielectric Spectroscopy

 
mfia impedance

MFIA
500 kHz / 5 MHz Impedance Analyzer
0.05% basic accuracy
Applications: Electrical engineering: sensors, semiconductor characterization, ultra-high resistors, dielectric material characterization, structural health monitoring, dispersion monitoring

   
dielectric thermal analysis Advanced Dielectric Thermal Analysis
System (DETA-SCOPE) by ADVISE. 
Excitation voltage 10 V. Frequency range 0.01 Hz to 1MHz
   

EMI Shielding infrastructure – Set up

keysight network

P9372A Keysight Streamline USB Vector Network Analyzer, 9 GHz
Measurement speed: 24 msec (201 points, full 2-port cal, 100 kHz IFBW)
Dynamic range: > 114 dB at 9 GHz > 110 dB at 20 GHz (10 Hz IFBW)
Trace noise: < 0.003 dBrms (1 kHz IFBW)
Stability: 0.005 dB/degree C up to 4.5 GHz

   

Four-probe sheet resistance & electrical conductivity meter

oscila 4prob

Ossila 4prob
The most common technique used for measuring sheet resistance is the four-probe method. This technique involves using four equally-spaced, co-linear probes (known as a four-point probe) to make electrical contact with the material.
Applications: Material characterization, Thin-film Solar Cells and LEDs

   
textronics pulse gen Textronics AFG3052C dual channel pulse generator
   
textronics osc Textronics dual-channel Oscilloscope (TDS 2002C)
   
manson powersupply

DC power supply (Manson, 0.1 – 30V)

   

Thermoelectric materials and thermoelectric generator (TEG) characterization

thermal gradient stage

Thermal gradient stage with PLC controlled Peltier for thermoelectric material measurements (-20oC to 200oC)

   

hotplates

Hot plates and Voltage/ Current multimeters (Agilent 34401A6½) for thermoelectric generator (TEG) characterization.

   

News

Multifunctional Composite Materials

Guest Editor: Prof. Dr. Alkiviadis S. Paipetis

https://www.mdpi.com/journal/applsci/special_issues/multifunctional_composite_materials

 

Special Issue Information

Dear Colleagues,
Composite materials have been studied for several decades already. Particularly in the last decade, the use of structural composites materials has literally been booming in the aeronautics and automotive industry. This is marking a notable change in design mentality, i.e., the tailoring or “architecturing” of material in accordance with structural needs, a possibility uniquely offered by advanced composites. It is this mentality that gave birth to the next generation of composites, that of multifunctional composite materials. These materials made “by design” possess the required improved specific properties but are also equipped with additional properties which impart to them other functionalities, which may be structural or nonstructural.
To this aim, the hybridization of otherwise “traditional” composites has been widely studied. A typical case study is that of embedding nano-scaled reinforcement into the matrix of usually micro-scale reinforced systems, with a view to both enhancing the matrix dominated properties as well as imparting multifunctionality. In the literature, the additional functionalities provide diverse nonstructural capabilities, such as inherent structural health monitoring, sensing and actuation, power harvesting, and power storage, in addition to structural ones such as wear resistance, morphing or self-healing. The parallel structural and nonstructural capabilities of the new generation composites aim to enhance product life and increase product utility with minimum structural aggravation.
Functionalities imparted to the materials may be passive, active or even adaptive. For example, a material is subjected to a certain field during its service life. Thus, the material has to first sense the field effect, and, if it possesses some degree of “awareness”, evaluate it and even respond so as to adapt in order to retain its performance requirements. To perform these functionalities, there are power and coupling requirements. Additional to these requirements, the reliability and durability of such systems is also a major issue, as the functional properties need to extend throughout the service life of the material. Finally, one the major challenges related to multifunctionality is the provision of engineering to integrate these functionalities in the composite structure at a system level, whereby the architectured composite system will be enabled to perform the full cycle, i.e., sense–evaluate–react, in response to the external stimuli, be they mechanical, environmental or other.
This is an outline of the issues that form the scope of this Special Issue. Research papers are invited in relation to multifunctional advanced composite materials, smart materials, sensing and self-diagnosis, actuation and morphing, inherent energy harvesting and storage capabilities, environmental property enhancement, electromagnetic shielding, and in any other field where the materials by design perform in diverse ways so as to respond successfully to their service conditions.

Prof. Dr. Alkiviadis S. Paipetis
Guest Editor

 

Keywords

  • self-sensing and self diagnosis
  • self-healing
  • actuation and morphing
  • electromagnetic shielding
  • power harvesting and storage
  • structural health monitoring

CSML as the coordinator of the H2020 “HARVEST” project organizes a dissemination session for the project at the 9th International Conference on Innovation in Aviation and Space (EASN) which will be held in Athens on 4th September 2019. More Information can be found under https://easnconference.eu/home.

Visit of Klaus Friedrich, Emeritus Professor and Research Consultant, Institute for Composite Materials (IVW GmbH)
Seminar entitled: “MARKETS AND TRENDS IN THE APPLICATION OF POLYMER COMPOSITES”,
Wednesday 12 June 2019 at 11:00 am, at the premises of our Department, room ΚΥ1

The 18th international conference on fracture and damage mechanics (FDM 2019) will take place in Rodos (Rhodes), Greece. The conference series has the support of the experts in the field of fracture and damage mechanics and has become established as a leading international forum for presentation latest research. The high quality researches presented at the previous meetings are archived in conference proceedings published in book form. In addition special issues in leading journals such as International Journal of Fracture, Engineering Fracture Mechanics and Key Engineering Materials have been devoted to the work presented at the meeting. The proceedings one the 18th international conference will be published in the Journal of Key Engineering Materials and distributed to the delegates at the conference..

Conference organisers:
Professor Alkis Paipetis
University of Ioannina
and
Professor Ferri M.H.Aliabadi,
Imperial College, London

For further information please visit:
http://fdm.engineeringconferences.net/new/

User Login

© 2015 Composite and Smart Materials Lab (CSMLab) - Materials Engineering Department, University of Ioannina | Developed by Antonis Tzounis

Search